Home»Commentary»ATF Targets Pistol Stabilizing Braces in New Rulemaking

ATF Targets Pistol Stabilizing Braces in New Rulemaking

0
Shares
Pinterest WhatsApp

Article first appeared on Ammoland.com

U.S.A. -(AmmoLand.com)- On June 7th, ATF published a new notice of proposed rulemaking on its website entitled Factoring Criteria for Firearms with Attached “Stabilizing Braces”The proposed rule has not yet been published in the Federal Register, and interested parties will have 90 days to comment on the proposed rule once it is published.

The rule seems aimed at making nearly all configurations of firearms equipped with stabilizing braces subject to the taxation and registration requirements of the National Firearms Act.

Since 2012, ATF has recognized that stabilizing braces serve a legitimate function and the inclusion of a stabilizing brace on pistol or other firearm does not automatically subject that firearm to the provisions of the NFA. That’s because stabilizing braces were first designed and intended to help disabled veterans fire large format pistols.

In the intervening years, ATF has repeatedly confirmed that the inclusion of a stabilizing brace on a firearm does not make that firearm subject to the NFA. While there was a limited time between 2015 and 2017 where ATF claimed that using a stabilizing brace as a shoulder stock could “redesign” the firearm and create an NFA firearm, ATF has never taken the position that the mere inclusion of a stabilizing brace on a firearm makes it an NFA firearm.

Until now.

It should come as no surprise that the most anti-gun administration in American history would bend (and break) the rules to suit their gun control ends. The new proposed rule would make nearly all configurations of firearms with stabilizing braces into NFA firearms.

The proposed rule lays out a points system, similar to the one used for handgun importation, to determine if a given firearm when equipped with a stabilizing brace is and NFA firearm. But, unlike the handgun importation criteria, the new factoring system seems designed to ensure that few, if any, firearms can meet the criteria.

The new factoring criteria are split into three parts. First, the firearm with attached stabilizing brace must weigh at least four pounds and be between 12 and 26 inches long. Assuming the firearm fits in these parameters, then the brace is evaluated for certain features, and finally the entire firearm with brace is evaluated for a different, but similar, set of features. If the firearm receives too many arbitrarily assigned points, then it will be classified as a short-barreled rifle.

While some of the listed criteria might tend to indicate the utility of using a given firearm with a stabilizing brace, many seem entirely arbitrary, and their inclusion is clearly aimed at ensuring that certain stabilizing brace designs that ATF does not like cannot escape classification under the NFA.

For example, ATF apparently considers the physical appearance of a brace, and whether it looks similar (in ATF’s determination) to a known stock design, as an important factor in determining the utility of firing a given firearm from the user’s shoulder. Perhaps even more arbitrary, the ATF will consider how the brace attaches to the host firearm when determining if the firearm is intended to be fired from the shoulder.

Even where the criteria may give some indicia of the intent of the stabilizing brace’s design, such as rear surface area, which could gauge the utility of using the brace to fire from the shoulder, ATF sticks to arbitrarily evaluating the criteria. Rather than an objective rear surface area measurement in square inches, ATF will evaluate the rear surface of a brace to fit into four categories.

Those are:

“Device incorporates features to prevent use as a shouldering device”

“Minimized Rear Surface lacking features to discourage shouldering”

“Rear Surface useful for shouldering the firearm”

“Material added to increase Rear Surface for shouldering”

It’s unclear how gun owners are supposed to apply such an ill-defined standard, and the proposed rule is full of such problems. The rear surface area criteria also highlight that very little thought was put into many of the criteria. If a pistol stabilizing brace “incorporates features to prevent use as a shouldering device” that should mean that any firearm using that brace is per se not “designed . . . made . . . and intended to be fired from the shoulder.” Any firearm equipped with such a device should not be able to be classified as a short-barreled rifle.

ATF also does not acknowledge that the proposed rule would reverse nearly a decade of ruling that the agency has provided to manufacturers and gun owners. Federal law is very clear that an administrative agency changing its position must “display awareness” of the change and give a “reasoned explanation” for the new position. ATF fails to do either in the proposed rule.

While the government is not yet accepting comments, please check back to www.nraila.org soon for more information on how you can help stop the Biden Administration’s latest executive overreach.


About NRA-ILA:

Established in 1975, the Institute for Legislative Action (ILA) is the “lobbying” arm of the National Rifle Association of America. ILA is responsible for preserving the right of all law-abiding individuals in the legislative, political, and legal arenas, to purchase, possess, and use firearms for legitimate purposes as guaranteed by the Second Amendment to the U.S. Constitution. Visit: www.nra.org

Don't forget to like us on Facebook and follow us on Twitter.

Previous post

Multiple Gun Control Bills Head To Colorado Governor’s Desk

Next post

The Ruling By A California Judge That Smacked Down "Assault Weapons" Ban You Really Must Read